HOBBYMATE D6 Elite review: More than a drone charger

In the past, chargers were very basic electronic devices. I remember that ones I tried to repair one and I found inside only couple of resistors and diodes. Compared to those old charges, the  HobbyMate D6 Elite is a very versatile hi-tech gear. In addition to the fact that allows to charge almost any type of rechargeable batteries (multi-chemistry), it can be used as servo tester as well. Moreover, thanks to the XT60 input, it can be used as emergency power-bank.

While most of the drones come with their own dedicated charger, they are not necessarily the best option. For example, the FiMI A3 is packed with a basic charger which doesn’t allow to fully charge the LIPO. Using the HobbyMate D6Elite charger I obtained 4 minutes of extra flight time.

Sponosored AD

HobbyMate D6 Elite core features

  • Charging, Discharging, Storage charging, Cell checker and Servo tester;
  • PWM, PPM and SBUS Input/Output receiver & flight control tester;
  • Multi-chemistry (LiPo 1-8S, LiHV 1-8S, LiFe 1-8S,NiMh 1-20S annd PB 1-12S);
  • Can charge up to 8 cell Li-Po batteries;
  • Wide range of DC input ( 7~30V@MAX 16A) – XT60 plug;
  • Integrated 2.2 inch (132*64 Pixel) black and white LCD;
  • Intelligent dual cooling system (variable speed);
  • USB 5.0V@5.1A output for mobile devices.

HOBBYMATE D6 Elite charger review

Disclosure: I received this pocket drone charger as part of a product review collaboration with HobbyCool. Although the product was offered free of charge, all opinions in this review remain my own and I was in no way influenced by the sponsor.

HobbyMate D6 Elite review: Box content

HobbyMate D6 Elite review: Box content

I received the package in about 3 weeks with standard free shipping. The box is very small and includes, besides the charger, only a USB Type A cable and a tiny user manual. No battery adapters nor AC/DC adapter included.

At a glance

The HOBBYMATE D6 Elite is one of the smallest 8s balance charger that I had in my hand. Anyway, despite its small size, it looks pretty nice. On front panel there is a 2.2″ monochrome LCD screen, a dial-knob (with center “OK” button) and “Exit” button. On left side you can find the USB port (5V@2.1A) and the Servo socket (-,+,signal) which makes this charger quite unique. Battery plugs (XT60 and 1-8S balance socket) are found on the right side of the charger. Yes, it is capable to charge up to 8 cell LIPOs, not just 6 ones like other hobby chargers.

HobbyMate D6 Elite review: Design

HobbyMate D6 Elite review: Design

While its twin brother, the HobbyMate D6 Duo, comes with built-in AC/DC adapter, the D6Elite requires external power source. As I previously mentioned, for this purpose you have only a XT60 plug. If you want to charge one battery with another one, it is fine, but trust me this will not work forever. As power source you can use any DC adapter with 7-30 volts as well as a 2-7S LI-PO battery. If you will use a LIPO battery to power the charger, I suggest you to correctly set the input limit (3V/cell). For example, in case of a 6S LIPo you should set 18V.

On both sides of the XT60 input plug there is a tiny cooling fan. They start to spin only as it is getting hot inside the charger.

User interface (main menu)

Powering on the charger, it enters automatically into main menu where you have 4 options:  Charger, Output, Measurer and Settings. Navigating within menus can be done easily using the dial knob, OK and Exit button.

HobbyMate D6 Elite review: User interface

HobbyMate D6 Elite review: User interface

1. Charger – menu

By default, it comes with only one predefined battery type (LIPO). The user can freely add/remove and customize its charging programs (battery type, max cell voltage, charge current and discharge current). You can change charging current even on the fly (while the battery is charged). If you select LIPO, LiHV or LiFe battery type, you can start 3 different programs: Storage, Discharge and Charge. BTW, the number of cells are automatically detected, which is pretty cool.

HobbyMate D6 Elite review: Charging menu

HobbyMate D6 Elite review: Charging menu

2. Output mode

  • PWM – 1 channel – it allows to control/test motors from a gimbal;
  • PWR – 8 channels – it allows to test inputs of a flight controller (simulate a receiver);
  • sBUS -16 channels – it allows to test inputs of a flight controller (simulate a receiver);
  • PWR – Surely, this function will be appreciated by any electronics hobbyist. In this mode, the charger behaves as a step-up/step-down voltage/current regulator. You can adjust output voltage even on the fly. Here are also some predefined settings for: Mavic2 – 17.6V, Mavic S – 13.0V, Phantom S – 17.4V and Inspire S – 26.1V.

HobbyMate D6 Elite review: Output mode

HobbyMate D6 Elite review: Output mode

3. Measure mode

  • PWM – allows to measure receiver outputs (one channel at the time);
  • PPM – allows to measure receiver outputs (up to 8 channels at the time);
  • sBUS – allows to measure receiver outputs (up to 16 channels at the time);
  • BATT – allows to monitor each cell voltage, total voltage and state of charge (SOC).
  • ESC – Can simulate the throttle stick of the transmitter while measures the power which is absorbed by the motor through the ESC.

HobbyMate D6 Elite review: Measures mode

HobbyMate D6 Elite review: Measures mode

4. Settings Menu

  • Lowest input (min 7.0V);
  • Input power (max 350W);
  • Safe Temp. (by default 70° C);
  • Safe CHG time (by default 120 minutes);
  • DisCHG mode (Internal or Recycle);
  • sBus value (Original or Width);
  • Back-light level (1-10);
  • Contrast (1-10);
  • Buzzer (1-7);
  • Idle beep (by default 5 minutes);
  • Hub support (Off/On);
  • Language (English/Chinese);
  • Factory defaults;
  • ID and firmware versions.

Features I personally tested:

First thing I did, it was to make a 12V DC (female 2.1mm) to XT60 adapter cable. As I previously mentioned, you can’t charge batteries with another battery for too long. Even if it is the dream of mankind :D.

HobbyMate D6 Elite review: XT60 to DC cable

HobbyMate D6 Elite review: XT60 to DC cable

In addition to the standard stuff (charging, storage charging and discharging) I tested the PWR function, the Servo tester and sBUS monitor. Practically a bit of everything 🙂 All extra features worked great and they are very handy.

HobbyMate D6 Elite review: sBUS test

HobbyMate D6 Elite review: sBUS test

During discharge, the charger became pretty hot even if the cooling fans worked at full speed. For discharge, you have two options: internal and recycling. The second mode is pretty awesome, practically you transfer the capacity from one LI-PO to another one.

Through the USB port you can charge standard USB devices (smartphones, tables and toy drones). Yes, another bonus! Together with a LIPO battery it can be used as power-bank for mobile devices.

HobbyMate D6 Elite review: sBUS measure test

HobbyMate D6 Elite review: sBUS measure test

One more thing, if you connect the battery to the output (both cables), the charger starts automatically in cell checker mode. Will show you the balance state (voltage of each cell), total battery voltage and SOC (State Of Charge) in percent.

HobbyMate D6 Elite review: PWR mode test

HobbyMate D6 Elite review: PWR mode test

An the last thing, you can enter into calibration mode, by holding the center button while you connect the battery.

Price & Availability

This compact but fully-featured LIPO charger can be found here for only $39.90. If you have an Amazon account, you can also order it from there.

Editor’s ratings

  • Price/performance ratio
  • Design and build quality
  • Battery compatibility
  • Cell compatibility

Verdict

Whether if you are in the state of designing, testing, charging or troubleshooting your drone, the D6 Elite is your best mate :). It allows to measure the power usage in order to calculate the ESC rating. You can limit the output power in the testing phase. Moreover, it can be used as servo tester and cell checker. It allows to check the connection between the receiver and transmitter. Last but not least, it allows to charge almost any type of drone battery.

Just like in case of the other two reviewed HobbyMate chargers, my only complain is regarding the lack of included battery adapters. You are limited to XT60 plug, in case you don’t purchase some additional battery conversion cables.

User Review

4.5 (2 votes)

HobbyMate D6 Elite review: Verdict

HobbyMate D6 Elite review: Verdict

What I liked

  • Extremely affordable;
  • Many features (chargingdischarging, cells checker and servo tester);
  • Multi-chemistry (many types of batteries are supported);
  • You can change charging current while program is started (on the fly);
  • Internal and Recycling discharging;
  • Charger detects automatically number of cells;
  • Easy to use interface;
  • Can work as voltage/current regulator.

What I didn’t liked

  • Only XT60 input;
  • No internal AC/DC adapter;
  • Lack of included battery adapters.
Photo gallery
Alternatives

Frankly, it is very hard to find such versatile charger like the HobbyMate D6Elite. Especially so cheap and compact. IMHO, it is a quite unique product in its price tag. It combines the functionalists of at least 3 separate devices (charger, servo tester and battery meter).

Banggood AD

Source link

Spread the love

Alex Admin

Passion for planes, flights, aeronautical engineering and eager to share my knowledge and related areas of interest.

Leave a Reply

Your email address will not be published. Required fields are marked *

%d bloggers like this: